§21-11R, -13. Sealed access plates R tank, installed fuel drains

As expected, it wasn't difficult to apply B2 sealant to the access plates on the top of the right tank.  Overall, it took about an hour and about 3/4's of the jar of sealant.

As expected, it was much more difficult than it should have been to install the fuel drains.   The instructions on page 13 are deceptively simple -- Install (1) into (2), where (1) and (2) refer to the fuel drain and fuel tank, respectively.  It doesn't mention using anything to create a seal, but I know that those types of threads (NPT) aren't actually fluid tight and must have a sealant of some sort.   Basically, it boiled down to using B2, as is used everywhere else, or Loctite 565 which is called out in a different chapter but never mentioned in the actual instructions.  I posted a query on VAF and was told RTFM (section 5) where it generically calls out Loctite 565, so that's what I went with.

As mentioned a few posts ago, I had tried a simple trial fit by installing (finger tight only) those components, and somehow managed to strip threads.  I wasn't really sure if they were stripped inside the tank (horrible) or just on the $30 part (not too bad).   

I researched the drain and found that it was a 1/8" NPT.  I couldn't find any technical description of the threads for the part from Van's.  It appears that all 1/8" NPTs are 27 pitch but that was only because that was the only pitch number I ever encountered and it was rare to find it at all.  I bought a set of cheap taps & dies at Harbor Freight that included the desired NPT.  I've tapped internal threads before, but never cut or chased external threads.

Some scrap Al from the RV12 was used to make a test hole with the tap and I was able to thread the fuel drains into that.  This confirmed that they were indeed 1/8 NPT 27.  I debated chasing the external threads on the drains, but wasn't sure which side of the die was the starting side.  Since NPTs are tapered, doing it backwards would probably destroy the part, so I deferred.  In retrospect, I think running the drains through the test hole actually chased them a little anyway.

The tap was used to very gently chase the tank.  I only used finger pressure and no tools.  The drains got gooped up with 565 and I tried to install them.   Nope, the threads wouldn't engage.  I finally got them to engage and tighten by pushing up on the drain with my thumb to and apply a fair amount of axial load while gingerly rotating them with a closed 1/2" wrench.  Finally, success.  It only took an hour to install two bolts.

Right Fuel Drain

§21-07 thru -10, -11 L, -12. Installation of fuel senders, access ports, fuel caps

Two days ago I got a lot done and pretty much finished sealing up the Left tank.  I ran out of time, energy and sweat and didn't seal the access plates on the Right tank, but that is now one of those "just get 'er done" things since I've gone through the process and know what / how to do. 

To explain; we left off with both tanks inspected and rinsed w/ 100LL avgas.  There was no debris and we found nothing in the rinse process.  The tanks had a few days to dry before I got to work on Monday.  The plans call for bending the float attach arms for the two fuel senders and give some engineering drawings to show how to do it.  I did both of them backwards.  Luckily, it turns out that that configuration is perfectly acceptable.  The only variation is that the float arms are 'pointing' in the direction opposite of the drawing, but this is on an axis that is parallel to the actual pivoting, so it makes no difference.  (sin 0° = sin 180°).

The R fuel float was very stiff and would actually stay in whatever position I put it. This is not going to give an accurate fuel level measurement since the goal is for the float to fall by gravity and float by buoyancy in the fuel.   I actually didn't realize this until after I had applied the pro seal (or "B2", as Van's now calls it) and was in the middle of trying not to make a thorough mess.  I was able to gently apply a little bend in the mechanism such that it no longer was binding and free falls properly.

Right Fuel Sender, Internal View

I got both fuel senders sealed in place with the left over B2 sealant from the second flap.   It definitely was harder to work with and was getting stringy towards the end, so I'm pretty sure that it only had a few minutes of shelf life with which to work, but it was still spreadable enough that I'm comfortable that I have good seals on the fuel senders.   We'll find out soon.

Right Fuel Sender, External View

The inspection ports on the Left tank weren't too bad, but I was surprised that I used up most of a jar of B2.  I have one left in the freezer to do the Right tank later today.

As mentioned last time, I stripped the threads from the L fuel drain.  I have the 1/8' NPT tap from Harbor Freight and will address that later today, too.  With that done, the R tank will be curing for 24-48 hours and I'll start pressure testing the Left.

Stay tuned.